Methacrylic acid is colorless crystal or transparent liquid with pungent odor. Soluble in hot water, soluble in most organic solvents such as ethanol and ether. Easily polymerized into water-soluble polymers. Combustible, there is a danger of burning in case of high heat and open flame, and it can produce toxic gas when heated.

Antioxidant is a kind of chemical substance. When it is only a small amount in the polymer system, it can delay or inhibit the progress of the polymer oxidation process, thereby preventing the aging of the polymer and prolonging its service life. It is also called " Anti-aging agent".

Chemical nature: Forbidden qualitative: strong oxidizing agent, strong reducing agent, strong acid, strong base. Ecological nature: Ecotoxicity EC50: 1.2 ~ 1.51mg / L (luminous bacteria, microtox toxicity test) Biodegradability Miti-I test, initial concentration of 100 mg / L, sludge concentration 30 mg / L, 2 weeks later degraded 77%. Non-biodegradability In the air, when the hydroxyl radical concentration is 5.00 × 105 / cm3, the degradation of the half-life is 7.8d (theory). Other harmful effects The material is damaged by the environment and should pay spe

A substance that can reduce the surface tension of water, solution, suspension, etc., prevent the formation of foam, or reduce or eliminate the original foam. [1]

1.4, 4 '- methylene bis (2-chlorocene) The molecular weight is 267.15, the molecular formula is C13H12N2 CL2

HCFC-141b (monofluorodichloroethane) is a high-purity liquid widely used in cleaning and solvent fields. Because its damage to the ozone layer is 1/10 of CFC-113, it is designated as an ideal substitute for fully halogenated chlorofluorocarbons. HCFC-141b is a widely used non-perhalogenated chlorofluorocarbon. Although its destructive effect on the ozone layer has been greatly reduced compared to fully halogenated chlorofluorocarbons, it can still cause damage to the ozone layer that is difficult to recover. As a result, its use is gradually being reduced around the world.

Physical and chemical properties: (1) Melting point (° C): - 2 (2) Boiling point (° C): 158 (no water) (3) Relative density (water = 1): 1.46 (4) Relative density (air = 1): no material (5) Solubility: dissolved in water, alcohol, ether, insoluble in benzene, petroleum ether (6) Stability: unstable, protected from light (7) Preventing the conditions of touch (taboo): strong acid, strong alkali, acyl chloride, alcohol, amine, flammable or combustible materials.

Appearance: watery bright liquid with pleasant ketone-like fragrance. Main uses: Used as a solvent for spray paint, nitrocellulose, some fiber ethers, camphor, grease, natural and synthetic rubber. Precautions for storage and transportation: Store in a cool and ventilated warehouse. Keep away from kindling and heat sources. The warehouse temperature should not exceed 30℃. Avoid direct sunlight. Keep the container sealed. It should be stored separately from oxidant. Lighting, ventilation and other equipment in the storage room should be explosion-proof.

Appearance and traits: white crystals, extremely salty, non -toxic. It is easy to solverate in water, ether, glycerin and alkali, slightly soluble in ethanol, but insoluble in water -free ethanol, which is hygroscopic and easy to lump; New potassium salt is generated by reciprocating and disintegrating.

HCFC-141b (monofluorodichloroethane) is a high-purity liquid widely used in cleaning and solvent fields.

There are two isomers of 2,4-toluene diisocyanate and 2,6-toluene diisocyanate (TDI). According to the content of the two isomers, there are three standard products in the industry: (1) TDI-65 contains 2,4-TDI65%, 2,6-TDI35%; (2) TDI-80 contains 2,4- TDI80%, 2,6-TDI20%, more common; (3) TDI-100 contains 2,4-TDI100%. Carbon dioxide occurs with water effect. Easy to work with compounds containing active hydrogen atoms. Linear polyurethane or polyurethane resin with diol effect.

it can also be used as high octane gasoline components, is an important raw material for organic chemicals. It can also be used to remove the bitumen of the body. The hospital pathology is primarily used for tissue, slice of pilot and dewaxing.

This product is the standard configuration of SCR technology, the solution concentration is 32.5% 0.7%, which can effectively reduce exhaust pollution and ensure engine efficiency ;8-stage pretreatment + RO reverse osmosis technology + EDI electrodeionization water purification technology + high-precision filtration and purification to ensure the purity of the solution from the source, Delay SCR scaling, protect the urea pump and pipeline; select ultra-high-purity urea particles, made through multiple purification processes, long-term maintenance of the system and catalyst activity, and prol

In the textile industry, it is used as a dispersant for fiber lubricants and chemical fiber oils, as well as automotive brake fluids, pesticide dispersants, dry cleaning agents, cutting oil solvents, organic synthesis intermediates, auxiliary solvents for mineral oil emulsions, and analytical reagents.

Carbonide is a kind of inorganic compound with CS2 chemical formula. It is a colorless liquid and is a common solvent.

Methyl 2-chloropropionate is an organic compound with the chemical formula C4H7ClO2, mainly used as an intermediate in pesticides, pharmaceuticals, and spices.

Biphenyl, whose molecular formula is C12H10, is an important organic raw material and is widely used in the fields of medicine, pesticides, dyes, and liquid crystal materials.

Sodium peroxide is an inorganic substance with a chemical formula of Na2O2 and a molecular weight of 77.98. Beige powder or granules. The relative density is 2.8.

Solubility: insoluble in water, soluble in most organic solvents such as alcohol, ether.

Glycerol, also called glycerol, with the chemical formula c3h8o3, is colorless, odorless, sweet, with a clean and viscous liquid appearance. it's miles an organic substance that may take in moisture from the air, as well as hydrogen sulfide, hydrogen cyanide and sulfur dioxide. insoluble in benzene, chloroform, carbon tetrachloride, carbon disulfide, petroleum ether and oils, it's miles the skeleton factor of triglyceride molecules.

Appearance: Light yellow to white granular crystals (semi-circular) white to light yellow loose crystals, heating is made black. Microfincture. Content: ≥ 85% Melting point: 98-102 ° C Dry loss: ≤0.2%

Only a small part of ammonia molecules react with water to form ammonia monohydrate, which is a weak base that only exists in ammonia.