Sodium Persulfate is also called sodium sulfate, is an inorganic substance, a chemical formula is Na2S2O8, and the appearance is a white crystal powder, odorless.

The solubility in water was 549 g / L at 20 ° C. Relative density 2.400 (deposit density: 0.7).

Sodium peroxide is an inorganic substance with a chemical formula of Na2O2 and a molecular weight of 77.98. Beige powder or granules. The relative density is 2.8.

Can gradually decompose, moist and high temperatures can accelerate decomposition. Can be decomposed by ethanol and silver ion.White crystalline powder.

Potassium hydroxide is strongly alkaline and corrosive, and its properties are similar to sodium hydroxide, which can cause burns. It can absorb water and dissolve in the air, and absorb carbon dioxide to gradually become potassium carbonate. The pH of the 0.1 mol/L solution is 13.5.

White oblique crystals, industrial products are white or light gray lumps or rods. Easily soluble in water, emits a lot of heat of dissolution when dissolved, soluble in ethanol, slightly soluble in ether. It is deliquescent and has strong water absorption. Potassium hydroxide is strongly alkaline and corrosive, and its properties are similar to sodium hydroxide, which can cause burns. It can absorb water and dissolve in the air, and absorb carbon dioxide to gradually become potassium carbonate. The pH of the 0.1 mol/L solution is 13.5.

The industrial neighborl xylene is a raw material, first washes the acid layer to the acid layer colorless, then use 10% sodium hydroxide solution, water is washed to pass, and the aqueous layer is separated, and the calcium chloride is borned with anhydrous carbon. After the distinction is low, the intermediate fraction is collected, that is, a pure product.

Solubility: Insoluble in water, acid and alkali, but soluble in organic solvents such as alcohol, ether and benzene.The preparation methods of biphenyl include the chemical composition method of making biphenyl through benzene pyrolysis and the separate extraction method of making biphenyl through various coal tar fractions. The mass fraction of biphenyl in coal tar is 0.20%-0.40%, and coal tar extraction method and chemical composition method coexist.

Appearance and properties: colorless liquid, almost odorless Molecular weight 90.12 Vapor pressure 0.51 kPa/20℃ Flash point: 43℃ Melting point -70°C boiling point: 135.1°C solubility can be miscible with water and most organic solvents such as ethanol Density (D4) 0.925-0.935

Oxygen is a colorless and odorless gas, and the most common elementary form of oxygen. Melting point is -218.4°C, boiling point is -183°C. It is not easily soluble in water, and about 30mL of oxygen can be dissolved in 1L of water. Oxygen in the air accounts for about 21%. Liquid oxygen is sky blue. Solid oxygen is blue crystals.

Dibenylmethane diisocyanate, referred to as "MDI", is an organic substance, a chemical formula C15H10N2O2.

There are two isomers of 2,4-toluene diisocyanate and 2,6-toluene diisocyanate (TDI). According to the content of the two isomers, there are three standard products in the industry: (1) TDI-65 contains 2,4-TDI65%, 2,6-TDI35%; (2) TDI-80 contains 2,4- TDI80%, 2,6-TDI20%, more common; (3) TDI-100 contains 2,4-TDI100%. Carbon dioxide occurs with water effect. Easy to work with compounds containing active hydrogen atoms. Linear polyurethane or polyurethane resin with diol effect.

M-xylene is an organic compound with a molecular formula C8H10, a molecular weight of 106, a colorless concussion liquid, a odor like toluene.

Common tetra-group lead, ferrocene, MMT (methylcyclopentadiene trikarbonyl manganese) or CMT is common, because metal deposits can occur in the inside of the launching machine, resulting in a cylinder wear, spark plug ignition Poor problems such as poisoning, oxygen sensors and ternary catalysts, have been prohibited or constrained. The addition of tetra-element and ferrocene added is known as national standards, and the manganese-based anti-explosive agent is strictly constrained (the detection limit is less than 0.018 g / L).

Industrial ammonia is an aqueous solution containing 25% to 28% ammonia. Only a small part of ammonia molecules react with water to form ammonia monohydrate, which is a weak base that only exists in ammonia.

Ammonia, also known as Amonia water, can be written as NH3(aq), which is an aqueous solution of ammonia, colorless, transparent and has a pungent odor.

Only a small part of ammonia molecules react with water to form ammonia monohydrate, which is a weak base that only exists in ammonia.

Aspirational antioxidants should have the following conditions: ①Should have high anti-oxidation ability; ②Good compatibility with resin, no precipitation; ③Good processing function, non-volatile and non-decomposing at the processing temperature of high polymer; ④Good resistance to extraction, insoluble in water and oil; ⑤The color of itself is best to be colorless or light-colored, so as not to pollute the product; ⑥Non-toxic or low-toxic; ⑦Low price. In fact, any kind of antioxidant can not fully meet these conditions.

Chemical nature: Forbidden qualitative: strong oxidizing agent, strong reducing agent, strong acid, strong base. Ecological nature: Ecotoxicity EC50: 1.2 ~ 1.51mg / L (luminous bacteria, microtox toxicity test) Biodegradability Miti-I test, initial concentration of 100 mg / L, sludge concentration 30 mg / L, 2 weeks later degraded 77%. Non-biodegradability In the air, when the hydroxyl radical concentration is 5.00 × 105 / cm3, the degradation of the half-life is 7.8d (theory). Other harmful effects The material is damaged by the environment and should pay spe

Hypromellose (Hypromellose), also called hypromellose, is one of the non-ionic cellulose mixed ethers.

Molecular weight: 65.39 Grade: 5N MDL number: MFCD00011291 EC number: 231-175-3

Colorless tasteless oily liquid, boiling point 343 ° C (0.101 MP), flash point (open cup) 204 ° C, freezing point -80 ° C, volatile rate 0.00009 g / cm, hour (105 ° C), hydrolysis rate 0.1% (100) ° C, 6 hours), soluble in most organic solvents. Resin compatible with polyvinyl chloride, polystyrene, vinyl chloride-vinyl acetate copolymer, nitrocellulose, ethylcellulose, polyvinyl butyal butyal. It is compatible with cellulose acetate and phrochloride cellulose.